Both the straight blade and v-plow feature an easy-on/easy-off mounting system and removable receiver brackets for exceptional ground clearance.
Blade Width: 6'0"
Fits: Full Sized UTVs & Series 1 Tractors
Moldboard: Powder-Coated Steel
THE IMPACT PLOW COMES IN MID-WEIGHT STRAIGHT BLADES ,AND HEAVY-DUTY STRAIGHT OR V-PLOW.
STRAIGHT — BLADE CONSTRUCTION
The IMPACT™ straight blade UTV plow features a 14-gauge powder coated steel moldboard that is 6′ wide and comes with a standard 5″ steel cutting edge.
STRAIGHT — BLADE CONSTRUCTION
The IMPACT™ straight blade UTV plow features a 14-gauge powder coated steel moldboard that is 6' wide and comes with a standard 5" steel cutting edge.
STRAIGHT — STRUCTURAL REINFORCEMENT
Four vertical ribs and high-strength, low-weight, alloy steel components ensure the plow is strong enough for commercial operation and light enough to fit more UTVs.
STRAIGHT — TRIP PROTECTION
Two heavy-duty coil springs protect your plow and UTV by allowing the whole blade to trip when striking obstacles.
V-PLOW — BLADE CONSTRUCTION
The IMPACT™ flared v-plow blades go from a 25¼" center height to a full 29¼" at the outer edge. The 14-gauge powder coated steel flared moldboard is 6' wide and comes with a standard 5" high-carbon steel cutting edge, reducing wear and extending the life of the blade.
V-PLOW — STRUCTURAL REINFORCEMENT
Six vertical ribs, coupled with high-strength, low-weight, alloy steel components provide a favorable strength-to-weight ratio, keeping stress off of the UTV frame. A 3/4" diameter, steel center pin resides within a three-connection-point hinge, keeping the wings tight for improved performance.
V-PLOW — WIDTH ADJUSTMENT
When fully angled or in V mode, the IMPACT™ UTV v-plow plowing path is 5' wide, and 4' 7" in scoop. For UTVs with a wider wheel base, a width-adjustment setting is available to make your plowing path wider in these positions. Using the alternate setting, the plowing width is 5' 6" when fully angled or in V, and 5' 1" in scoop.
V-PLOW — DOUBLE-ACTING CYLINDERS
A standard feature on the IMPACT™ UTV v-plow, UltraLock double-acting cylinders allow the operator to use the v-plow in straight blade mode by locking the wings together instead of having to toggle each wing independently. The double-acting cylinders also hold the wings firmly in place for clean, efficient back dragging.
V-PLOW — TRIP PROTECTION
Each blade features independent trip-edge design with heavy-duty coil springs for protection when encountering bumps and obstacles. Whether in V, scoop or straight blade configuration, the trip-edge helps protect the plow, the equipment, and the operator. Since only the edge trips, snow remains in front of the blade, so you can keep going without spilling the entire load of snow.
V-PLOW — STEEL CENTER GAP COVER
For the cleanest pass in any blade configuration, the IMPACT™ UTV v-plow has a snow control gap cover over the center hinge to help deflect and prevent snow from being lost over the top of the blade.
RELIABLE HYDRAULICS
We manufacture our own hydraulic components to ensure the highest standards of quality and reliability, so that you get a hydraulics system that's not only fast and responsive, but that's built to last season after season. Fully enclosed components are protected from the elements. Hydraulic Scrape Lock holds the blade down for more efficient scraping and clean back dragging.
GROUND CLEARANCE
The removable receivers and low profile undercarriage provide exceptional ground clearance and maximize the ramp angle, so your unit will be trail ready when the plow is not attached.
UTV MOUNTING SYSTEM
Hooking up the IMPACT™ v-plow or straight blade is simple. With the receiver brackets installed on your utility vehicle, either drive in or manually push the plow into the receivers. Push up on the headgear to engage the hitch pins in the receiver holes, then slide the handle to lock the hitch pins in place. Finally, connect the electrical plug. Detaching the plow is just as easy. The receivers are removable, to maintain ground clearance.
TRACTOR COMPATIBLE MOUNT KIT
Designed for easy installation onto a wide range of tractor models, these mount kits make it possible for the IMPACT heavy-duty straight blade and v-plow to fit on a compact tractor. They are flared both vertically and horizontally to ensure proper alignment and make the drive-in connection easier. The push beam, which makes up the front portion of the mount, can be quickly detached to allow for a loader attachment.